Electric Current

Electric current definition and calculations.

Electric current definition

Electrical current is the flow rate of electric charge in an electric field, usually in an electrical circuit.

Using water pipe analogy, we can visualise the electrical current as the water current that flows in a pipe.

The electrical current is measured in an ampere (amp) unit.

 

Electric current calculation

Electrical current is measured by the rate of electric charge flow in an electrical circuit:

i(t) = dQ(t) / dt

The momentary current is given by the derivative of the electric charge by time.

i(t) is the momentary current I at time t in amps (A).

Q(t) is the momentary electric charge in coulombs (C).

t is the time in seconds (s).

 

When the current is constant:

I = ΔQ / Δt

I is the current in amps (A).

ΔQ is the electric charge in coulombs (C), that flows at time duration of Δt.

Δt is the time duration in seconds (s).

 

Example

When 5 coulombs flow through a resistor for duration of 10 seconds,

the current will be calculated by:

I = ΔQ / Δt  = 5C / 10s = 0.5A

Current calculation with Ohm's law

The current IR in anps (A) is equal to the resistor's voltage VR in volts (V) divided by the resistance R in ohms (Ω).

IR = VR / R

Current direction
current type from to
Positive charges + -
Negative charges - +
Conventional direction + -

Current in series circuits

Current that flows through resistors in series is equal in all resistors - just like water flow through a single pipe.

ITotal = I1 = I2 = I3 =...

ITotal - the equivalent current in amps (A).

I1 - current of load #1 in amps (A).

I2 - current of load #2 in amps (A).

I3 - current of load #3 in amps (A).

Current in parallel circuits

Current that flows through loads in parallel - just like water flow through parallel pipes.

The total current ITotal is the sum of the parallel currents of each load:

ITotal = I1 + I2 + I3 +...

ITotal - the equivalent current in amps (A).

I1 - current of load #1 in amps (A).

I2 - current of load #2 in amps (A).

I3 - current of load #3 in amps (A).

Current divider

The current division of resistors in parallel is

RT = 1 / (1/R2 + 1/R3)

or

I1 = IT × RT / (R1+RT)

Kirchhoff's current law (KCL)

The junction of several electrical components is called a node.

The algebraic sum of currents entering a node is zero.

Ik = 0

Alternating Current (AC)

Alternating current is generated by a sinusoidal voltage source.

Ohm's law

IZ = VZ / Z

IZ  - current flow through the load measured in amperes (A)

VZ - voltage drop on the load measured in volts (V)

Z  - impedance of the load measured in ohms (Ω)

Angular frequency

ω = 2π f

ω - angular velocity measured in radians per second (rad/s)

f  - frequency measured in hertz (Hz).

Momentary current

i(t) = Ipeak sin(ωt+θ)

i(t)      - momentary current at time t, measured in amps (A).

Ipeak - maximal current (=amplitude of sine), measured in amps (A).

ω      - angular frequency measured in radians per second (rad/s).

t        - time, measured in seconds (s).

θ       - phase of sine wave in radians (rad).

RMS (effective) current

IrmsIeffIpeak / √2 ≈ 0.707 Ipeak

Peak-to-peak current

Ip-p = 2Ipeak

Current measurement

Current measurement is done by connecting the ammeter in series to the measured object, so all the measured current will flow through the ammeter.

The ammeter has very low resistance, so it almost does not affect the measured circuit.

What do you mean by electric current?

: a movement of electrons, either negative or positive (such like electrons) that is accompanied by such visible effects as the creation of heat and magnetic fields or chemical transformations Compare direct current, alternating current, and displacement current, and direct current.


See also

Write how to improve this page

CONTENTS
MaxTables
Follow Us
🠕